The method of installation for both materials is different. Most flake installations are made either by ‘broadcast’ or ‘spray on’, whereas for pebble installation, it is hand trowelled – something similar to cement screeding.
After installation:
For Epoxy Pebble overlay, the joint lines between the tiles (grout) will not be visible and this makes cleaning easier.
For Epoxy Flake overlay, the joint lines might be visible at certain angles.
At Porousway, we recommend pebble for floor and flake for wall.
HDB toilets are usually built in standard size (between 35 – 45 sqft) and thus we are able to offer at a standard pricing. The elimination for site visit reduces our operational cost and that cascades to the affordable pricing for our services.
The floor trap will not be covered.
Natural pebbles bonded with water-resistant resin (epoxy).
The materials will be prepared and mixed only on site. The overlay is hand-trowel (i.e. similar to cement screeding) over the existing flooring.
The only use of chemicals use will be the mixing of epoxy – combination of Part A and Part B. There will be no visible smell emitted during the reaction and curing process.
There will not be discolouration as the pebble are homogenous and the colours are not dyed on. However, the gloss (shine) from the epoxy will wear out overtime but the anti-slip properties will not be affect. The application of a ‘kiss coat’ after 3-4 years of usage will be able to bring back the shine.
Allow 7 hours for the newly completed surface to fully cure before stepping on it.
The surface is troweled and it will be flat to the feet but textured. The analogy of the ‘feel to the feet’ is that of stepping on fine sand-paper.
If the source of the leak is identified to be from the bathroom, we will first resolve the water leaking issue by coating the entire existing flooring with a layer of waterproofing. The waterproofing layer will require roughly four hours to cure before the overlay of pebble overlay above.
Depending on the location and severity of the issue, the pebble overlay might be able to address the issue.
There will be one year warranty against workmanship and material defects.
We will be able to provide spot repair.
Please note that there will be slight colour difference as each batch of natural pebbles are different.
Both options are possible. The pros of installation of accessories first is the concealment of silicon (e.g. around toilet bowls) and also minimizing touchups. The cons of installation first arises when there is a change in fixture.
As the overlays are the finishing products, we recommend the installation of accessories first to minimize any touchups that might be required.
The anti-slip property is inherent to the pebble flooring and will not wear off. With regular and proper maintenance, the flooring will be in good condition even after 8 years (or more) of daily usage.
For a normal HDB toilet flooring, it only takes 0.5 days.
Floor and wall overlay for one toilet will take between 2-3 days (depending on selection of wall material).
No removal of toilet accessories will be required. As the products are cast on site, we are able to lay it around any current fixtures (e.g. toilet bowl or basin).
Although the layer of epoxy acts as a sealer, it is not a waterproofing solution. If there are concerns of water leak, a layer of waterproofing will be recommended.
We accept PayNow and all major credit and debit cards. There is also the option for cash payment after job completion.
We accept PayNow and all major credit and debit cards and payment. There is also
the option for payment via cash after job completion. No down payment is required for orders below $1600.
There will be a 50% down payment for project value $1600 or more.
The order is confirmed when you complete the e-purchase. The installation team will be there at the scheduled slot for the installation.
Should there be any changes required to the order, please contact at us at 9633 6696.
Cleaning is easy as there will not be any grout lines (as seen in the pictures). We recommend using a hard bristle broom to scrub once a week. You can use bleach (Clorox) as the pebbles are 100% natural and colours not dyed on.
For such case, you can use something flat to slide across the floor to “hit” that runaway pebble. That pebble is glued only by its edges (by epoxy) and will come off when you hit it from the sides.
We recommend scrubbing at least once a week with a hard bristle broom.
Scatter washing powder on wet floor
Scrub uniformly (especially the corners)
Allow the soap bubbles to sit for 10-15 minutes
Scrub lightly and rinse off with water
If deeper cleaning is required, the use of diluted bleach is possible – the flooring won’t discolor.
The ‘oil’ is a by product after the installation. The floor will feel ‘normal’ after scrubbing it once with soap (i.e. washing powder).
50 Serangoon North Ave 4,
#05-03
Singapore 555856
Phone
+65 8333 7667
Website
http://lefong.sg
E-mail
enquiry@lefong.sg